Instead of iterating over all the available trap policers, only perform
the tests with three policers: The first, the last and the one in the
middle of the range. On a Spectrum-3 system, this reduces the run time
from almost an hour to a few minutes.
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
There are several test cases in the net directory are still using
exit 0 or exit 1 when they need to be skipped. Use kselftest
framework skip code instead so it can help us to distinguish the
return status.
Criterion to filter out what should be fixed in net directory:
grep -r "exit [01]" -B1 | grep -i skip
This change might cause some false-positives if people are running
these test scripts directly and only checking their return codes,
which will change from 0 to 4. However I think the impact should be
small as most of our scripts here are already using this skip code.
And there will be no such issue if running them with the kselftest
framework.
Signed-off-by: Po-Hsu Lin <[email protected]>
Reviewed-by: Ido Schimmel <[email protected]>
Tested-by: Ido Schimmel <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
Add devlink_trap_drop_packets_get function, as well as test that are
used to verify devlink (hard) dropped stats functionality works.
Signed-off-by: Oleksandr Mazur <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
In the commit referenced below, a check was added to devlink_lib that
asserts the existence of a devlink device referenced by $DEVLINK_DEV.
Unfortunately, several netdevsim tests point DEVLINK_DEV at a device that
does not exist at the time that devlink_lib is sourced. Thus these tests
spuriously fail.
Fix this by introducing an override. By setting DEVLINK_DEV to an empty
string, the user declares their intention to handle DEVLINK_DEV management
on their own.
In all netdevsim tests that use devlink_lib and set DEVLINK_DEV, set
instead an empty DEVLINK_DEV just before sourcing devlink_lib, and set it
to the correct value right afterwards.
Fixes: 557c4d2f78 ("selftests: devlink_lib: add check for devlink device existence")
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Some selftests may not need any actual ports. Technically those are not
forwarding selftests, but devlink_lib can still be handy. Fall back on
NETIF_NO_CABLE in those cases.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Add a helper that answers the cell size of the devlink device.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Changing pool type from static to dynamic causes reinterpretation of
threshold values. They therefore need to be saved before pool type is
changed, then the pool type can be changed, and then the new values need
to be set up.
For that reason, set cannot subsume save, because it would be saving the
wrong thing, with possibly a nonsensical value, and restore would then fail
to restore the nonsensical value.
Thus extract a _save() from each of the relevant _set()'s. This way it is
possible to save everything up front, then to tweak it, and then restore in
the required order.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Test that policers shared by different tc filters are correctly
reference counted by observing policers' occupancy via devlink-resource.
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Petr Machata <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
Generate packets matching the various control traps and check that the
traps' stats increase accordingly.
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
It can be derived dynamically from the trap's name, so drop it.
Signed-off-by: Ido Schimmel <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Add test cases that verify that each registered packet trap policer:
* Honors that imposed limitations of rate and burst size
* Able to police trapped packets to the specified rate
* Able to police trapped packets to the specified burst size
* Able to be unbound from its trap group
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Add test cases for packet trap policer set / show commands as well as
for the binding of these policers to packet trap groups.
Both good and bad flows are tested for maximum coverage.
v2:
* Add test case with new 'fail_trap_policer_set' knob
* Add test case for partially modified trap group
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Add two devlink port helpers:
* devlink port get by netdev
* devlink cpu port get
Signed-off-by: Shalom Toledo <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Currently the helpers assume pref 1 and handle 101. Make that explicit
and pass the values from callers.
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Add common part of all the tests - check devlink status to ensure that
packets were trapped.
Signed-off-by: Amit Cohen <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Add proto parameter in order to enable the use of devlink_trap_cleanup()
in tests that use IPv6 protocol.
Signed-off-by: Amit Cohen <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
l2_drops_test() is used to check that drop traps are functioning as
intended. Currently it is only used in the layer 2 test, but it is also
useful for the layer 3 test introduced in the subsequent patch.
l2_drops_cleanup() is used to clean configurations and kill mausezahn
proccess.
Export the functions to the common devlink library to allow it to be
re-used by future tests.
Signed-off-by: Amit Cohen <[email protected]>
Acked-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Add helpers to interact with devlink-trap, such as setting the action of
a trap and retrieving statistics.
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
For tests that create their network interfaces dynamically or do not use
interfaces at all (as with netdevsim) it is useful to define their own
devlink device instead of deriving it from the first network interface.
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Add helpers to obtain, set, and restore a pool size, and a port-pool and
tc-pool threshold.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Use devlink -j and jq for more accurate querying. Use cut -f-2 instead
of rev-cut-rev combo.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
As for the others, check help message output to find out if devlink
supports "resource" object.
Signed-off-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
This helper library contains wrappers to devlink functionality agnostic
to the underlying device.
Signed-off-by: Yuval Mintz <[email protected]>
[[email protected]: Split this out from another patch.]
Signed-off-by: Petr Machata <[email protected]>
Signed-off-by: David S. Miller <[email protected]>